What Is an H-Bridge? (2024)

An H-bridge is a simple circuit that lets you control a DC motor to go backward or forward.

You normally use it with a microcontroller, such as an Arduino, to control motors.

When you can control two motors to go either forward or backward – you can build yourself a robot!

What Is an H-Bridge? (1)

H-Bridge concept

Here’s the concept of the H-bridge drawn out with switches:

What Is an H-Bridge? (2)

A DC motor spins either backward or forward, depending on how you connect the plus and the minus.

If you close switches 1 and 4, you have plus connected to the left side of the motor and minus to the other side. And the motor will start spinning in one direction.

If you instead close switches 2 and 3, you have plus connected to the right side and minus to the left side. And the motor spins in the opposite direction.

The H-Bridge circuit

You can build an H-bridge with four transistors.

What Is an H-Bridge? (5)

Get Our Basic Electronic Components Guide

Learn how the basic electronic components work so that circuit diagrams will start making sense to you.

If you’re not sure how the transistor works, I recommend you read the article How Transistors Work first. From there you’ll learn that the transistor can work as a switch that you can open and close with the voltage on the base.

What Is an H-Bridge? (6)

Since the transistor can be a switch, you’ll be able to make the motor spin in either direction by turning on and off the four transistors in the circuit above.

Usually, you control the transistors from a microcontroller, such as Arduino.

What Transistors To Use?

The transistors you choose must:

  • Handle enough current
  • Use PNP (or pMOS) at the top
  • Have a low voltage drop between collector and emitter

Current

The most important thing is that all the transistors can handle enough current for the motor. Otherwise, it will burn out.

For example, if the motor draws 1 Ampere of current, you need transistors that can handle a minimum of 1 Ampere.

PNP (or pMOS) transistors at the top

Next, you see I have chosen PNP transistors on the top, and NPN transistors on the bottom.

What turns the transistor on or off is the voltage difference between the base and the emitter.

With PNP transistors at the top, you can use a higher voltage for VCC than you use for the base of the transistors.

For example, you can use 3.3V outputs from a microcontroller and 9V for Vcc.

That won’t work if you have NPNs at the top since the emitter will be 0.7V lower than the base. Because that turns into 3.3V – 0.7V = 2.6V at the positive side of the motor, no matter what VCC voltage you choose.

Low voltage drop between collector and emitter

While building a robot in Colombia, I tried to make this circuit using TIP120 and TIP127 transistors.

That did not work.

TIP12x transistors give a 2V drop from the emitter to collector.

In such a configuration, you’d end up with a loss of 4V over the transistors. I was trying to connect this to an Arduino, using its 5V supply, but failed because it was only 1V left for the motor!

Here’s a nice article/rant about the topic: Stop using antique parts!

Basically, it says that the TIP transistors are antiques that you shouldn’t use anymore because of this huge voltage drop.

Choose transistors with low voltage drop. For example BD135/BD136 or MOSFET transistors.

Protection diodes and PWM mode

A side-effect of how a motor works is that the motor will also generate electrical energy. When you disable the transistors to stop running the motor, this energy needs to be released in some way.

If you add diodes in the reverse direction for the transistors, you give a path for the current to take to release this energy. Without them, you risk that the voltage rises and damages your transistors.

What Is an H-Bridge? (7)

You can read more about this – and what to keep in mind if you want to use a PWM signal to control the speed of the motor, in this article.

The resistors going into each base are there to reduce the current to each transistor. Not sure how to calculate it? If you’re using a microcontroller to control them, start with 1k and adjust if that doesn’t work.

Questions or comments?

Have you built an H-bridge before? Or do you have questions about the H-bridge? Let me know in the comments field below:

More Transistors Tutorials

  • How Transistors Work
  • Transistor as a Switch
  • The Bipolar Junction Transistor (BJT)
  • The PNP Transistor
  • Insulated Gate Bipolar Transistor (IGBT)
  • MOSFET Gate Resistor
  • The Phototransistor
  • Transistor Circuit: Astable Multivibrator for Blinking
  • Transistor Circuit: H-Bridge for Motor Control

What Is an H-Bridge? (8)

Get Our Basic Electronic Components Guide

Learn how the basic electronic components work so that circuit diagrams will start making sense to you.

What Is an H-Bridge? (2024)

References

Top Articles
Latest Posts
Article information

Author: Amb. Frankie Simonis

Last Updated:

Views: 5711

Rating: 4.6 / 5 (76 voted)

Reviews: 83% of readers found this page helpful

Author information

Name: Amb. Frankie Simonis

Birthday: 1998-02-19

Address: 64841 Delmar Isle, North Wiley, OR 74073

Phone: +17844167847676

Job: Forward IT Agent

Hobby: LARPing, Kitesurfing, Sewing, Digital arts, Sand art, Gardening, Dance

Introduction: My name is Amb. Frankie Simonis, I am a hilarious, enchanting, energetic, cooperative, innocent, cute, joyous person who loves writing and wants to share my knowledge and understanding with you.